Attributes

attributes.py - Contains the ID of all attributes belongs to the module.

class nirfmxcdma2k.attributes.AttributeID(value)

Bases: Enum

This enum class contains the ID of all attributes belongs to the module.

ACP_ALL_TRACES_ENABLED = 6295585

Specifies whether to enable the traces to be stored and retrieved after performing the ACP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

ACP_AVERAGING_COUNT = 6295573

Specifies the number of acquisitions used for averaging when you set the ACP_AVERAGING_ENABLED attribute to True.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10.

ACP_AVERAGING_ENABLED = 6295574

Specifies whether to enable averaging for the ACP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measurement is performed on a single acquisition.
True (1)	The ACP measurement uses the value of the ACP Averaging Count attribute as the number of acquisitions over which the ACP measurement is averaged.

ACP_AVERAGING_TYPE = 6295576

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for ACP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is RMS.

Name (Value)	Description
RMS (0)	The power spectrum is linearly averaged. RMS averaging reduces signal fluctuations but not the noise floor.
Log (1)	The power spectrum is averaged in a logarithmic scale.
Scalar (2)	The square root of the power spectrum is averaged.
Max (3)	The peak power in the spectrum at each frequency bin is retained from one acquisition to the next.
Min (4)	The lowest power in the spectrum at each frequency bin is retained from one acquisition to the next.

ACP_CARRIER_INTEGRATION_BANDWIDTH = 6295557

Returns the ACP carrier integration bandwidth. This value is expressed in Hz.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

ACP_FAR_IF_OUTPUT_POWER_OFFSET = 6295606

Specifies the offset by which to adjust the IF output power level for offset channels that are far from the carrier channel to improve the dynamic range. This value is expressed in dB. This attribute is used only if you set the ACP_MEASUREMENT_METHOD attribute to Dynamic Range and set the ACP_IF_OUTPUT_POWER_OFFSET_AUTO attribute to False.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 20 dB.

ACP_FFT_OVERLAP = 6295610

Returns the number of samples to overlap between consecutive chunks while performing FFT.

This value is expressed as a percentage of ACP_SEQUENTIAL_FFT_SIZE attribute when you set the ACP_MEASUREMENT_METHOD attribute to Sequential FFT.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

ACP_FFT_OVERLAP_MODE = 6295609

Specifies how the FFT overlap is applied to the acquired samples.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default Value is Disabled.

Name (Value)	Description
Disabled (0)	Indicates that no overlapping is applied to the acquired samples.
Automatic (1)	Indicates that RFmx chooses optimal values of the ACP FFT Overlap (%) attribute based on the measurement configuration.

ACP_IF_OUTPUT_POWER_OFFSET_AUTO = 6295604

Specifies whether the measurement computes an IF output power level offset for the offset channels to improve the dynamic range of the ACP measurement. This attribute is used only if you set the ACP_MEASUREMENT_METHOD attribute to Dynamic Range.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement does not compute an IF output power level offset for the offset channels.
True (1)	The measurement computes an IF output power level offset for the offset channels.

ACP_MEASUREMENT_ENABLED = 6295552

Specifies whether to enable the ACP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

ACP_MEASUREMENT_METHOD = 6295570

Specifies the method for performing the ACP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Normal.

Name (Value)	Description
Normal (0)	The ACP measurement acquires the spectrum using the same signal analyzer setting across frequency bands. Use this method when measurement speed is desirable over higher dynamic range.
Dynamic Range (1)	The ACP measurement acquires the spectrum using the hardware-specific optimizations for different frequency bands. Use this method to get the best dynamic range. Supported Devices: PXIe-5665/5668R.
Sequential FFT (2)	The ACP measurement acquires I/Q the samples specified by the ACP Sweep Time. These samples are divided into smaller chunks. The size of each chunk is defined by the ACP Sequential FFT Size attribute, and FFT is computed for each these chunks. The resultant FFTs are averaged to get the spectrum used to compute the ACP. If the total acquired samples is not an integer multiple of the FFT size, the remaining samples at the end of the acquisition are not used. Use this method to optimize the ACP Measurement speed. The accuracy of results may be reduced when using this measurement method.

ACP_NEAR_IF_OUTPUT_POWER_OFFSET = 6295605

Specifies the offset by which to adjust the IF output power level for offset channels that are near the carrier channel to improve the dynamic range. This value is expressed in dB. This attribute is used only if you set the ACP_MEASUREMENT_METHOD attribute to Dynamic Range and set the ACP_IF_OUTPUT_POWER_OFFSET_AUTO attribute to False.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10 dB.

ACP_NOISE_COMPENSATION_ENABLED = 6295584

Specifies whether to enable compensation of the channel powers for the inherent noise floor of the signal analyzer.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	Disables compensation of the channel powers for the noise floor of the signal analyzer.
True (1)	Enables compensation of the channel powers for the noise floor of the signal analyzer. The noise floor of the signal analyzer is measured for the RF path used by the ACP measurement and cached for future use. If signal analyzer or measurement parameters change, noise floors are measured again. Supported Devices: PXIe-5663/5665/5668R, PXIe-5830/5831/5832/5842/5860

ACP_NUMBER_OF_ANALYSIS_THREADS = 6295572

Specifies the maximum number of threads used for parallelism for the ACP measurement.

The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1.

ACP_NUMBER_OF_OFFSETS = 6295560

Specifies the number of offset channels.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 2.

ACP_OFFSET_FREQUENCY = 6295562

Returns the frequency of an ACP offset channel relative to the carrier frequency. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

ACP_OFFSET_INTEGRATION_BANDWIDTH = 6295566

Returns the integration bandwidth of an ACP offset channel. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

ACP_RBW_FILTER_AUTO_BANDWIDTH = 6295579

Specifies whether the measurement computes the RBW.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the RBW that you specify in the ACP RBW attribute.
True (1)	The measurement computes the RBW.

ACP_RBW_FILTER_BANDWIDTH = 6295580

Specifies the bandwidth of the RBW filter used to sweep the acquired signal when you set the ACP_RBW_FILTER_AUTO_BANDWIDTH attribute to False. This value is expressed in Hz.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10 kHz.

ACP_RBW_FILTER_TYPE = 6295581

Specifies the shape of the digital RBW filter.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Gaussian.

Name (Value)	Description
FFT Based (0)	An RBW filter with an FFT-based response is applied.
Gaussian (1)	An RBW filter with a Gaussian response is applied.
Flat (2)	An RBW filter with a flat response is applied.

ACP_RESULTS_CARRIER_ABSOLUTE_POWER = 6295590

Returns the absolute measured carrier power. This value is expressed in dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

ACP_RESULTS_LOWER_OFFSET_ABSOLUTE_POWER = 6295596

Returns the absolute measured lower offset channel power. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

ACP_RESULTS_LOWER_OFFSET_RELATIVE_POWER = 6295597

Returns the lower offset channel power measured relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

ACP_RESULTS_UPPER_OFFSET_ABSOLUTE_POWER = 6295602

Returns the absolute measured upper offset channel power. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

ACP_RESULTS_UPPER_OFFSET_RELATIVE_POWER = 6295603

Returns the upper offset channel power measured relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

ACP_SEQUENTIAL_FFT_SIZE = 6295608

Specifies the FFT size, when you set the ACP_MEASUREMENT_METHOD attribute to Sequential FFT.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 512.

ACP_SWEEP_TIME_AUTO = 6295582

Specifies whether the measurement computes the sweep time.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the sweep time that you specify in the ACP Sweep Time attribute.
True (1)	The measurement uses the default sweep time of 0.001667 seconds.

ACP_SWEEP_TIME_INTERVAL = 6295583

Specifies the sweep time when you set the ACP_SWEEP_TIME_AUTO attribute to False. This value is expressed in seconds.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.0016667 seconds.

AUTO_LEVEL_INITIAL_REFERENCE_LEVEL = 6344704

Specifies the initial reference level that the RFmxCDMA2k Auto Level method uses to estimate the peak power of the input signal. This value is expressed in dBm.

The default value is 30 dBm.

BAND_CLASS = 6291472

1.5, Table 1.5- Band Class List, of the 3GPP2 C.S0057-F specification v1.0.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0. Valid values are 0 to 12, 14 and 15.

Type:

Specifies the band in which the channel is located as defined in Section

BRANCH = 6291481

Specifies the branch on which a specific user-defined channel is mapped. This attribute is used only when you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined.

Use “channel< <format type=”monospace-italic”>n</format> >” as the Selector String to configure or read this attribute.

The default value is I.

Name (Value)	Description
I (0)	Specifies the in-phase branch.
Q (1)	Specifies the quadrature branch.
I and Q (2)	Specifies the in-phase and quadrature branch.

CDA_ALL_TRACES_ENABLED = 6369295

Specifies whether to enable the traces to be stored and retrieved after performing the code domain analysis (CDA).

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

CDA_BASE_SPREADING_FACTOR = 6369285

Specifies the base spreading factor used to calculate the code domain power traces.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 64. The valid values are 2, 4, 8, 16, 32, and 64.

CDA_IQ_GAIN_IMBALANCE_REMOVAL_ENABLED = 6369292

Specifies whether to remove the I/Q gain imbalance before the code domain analysis (CDA) measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q gain imbalance is not removed before the CDA measurement.
True (1)	I/Q gain imbalance is removed before the CDA measurement.

CDA_IQ_OFFSET_REMOVAL_ENABLED = 6369291

Specifies whether to remove I/Q offset before the code domain analysis (CDA) measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q offset is not removed before the CDA measurement.
True (1)	I/Q offset is removed before the CDA measurement.

CDA_IQ_QUADRATURE_ERROR_REMOVAL_ENABLED = 6369293

Specifies whether to remove the I/Q quadrature error before the code domain analysis (CDA) measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q quadrature error is not removed before the CDA measurement.
True (1)	I/Q quadrature error is removed before the CDA measurement.

CDA_MEASUREMENT_CHANNEL_BRANCH = 6369288

Specifies the branch of a channel subject to channel specific analysis.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is I.

Name (Value)	Description
I (0)	Specifies the in-phase branch.
Q (1)	Specifies the quadrature branch.

CDA_MEASUREMENT_CHANNEL_WALSH_CODE_LENGTH = 6369286

Specifies the Walsh code length of a channel subject to channel specific analysis.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 64. The valid values are 2, 4, 8, 16, 32, and 64.

CDA_MEASUREMENT_CHANNEL_WALSH_CODE_NUMBER = 6369287

Specifies the Walsh code number of a channel subject to channel specific analysis.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0. The valid values are 0 to 63, inclusive.

CDA_MEASUREMENT_ENABLED = 6369280

Specifies whether to enable the code domain analysis (CDA) measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

CDA_MEASUREMENT_LENGTH = 6369284

Specifies the duration of code domain measurement. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1. The valid values are 1 to 16, inclusive. The sum of the CDA measurement offset and the CDA measurement length must be less than or equal to 16.

CDA_MEASUREMENT_OFFSET = 6369283

Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the CDA_SYNCHRONIZATION_MODE attribute. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0. The valid values are 1 to 15, inclusive. The sum of the CDA measurement offset and the CDA measurement length must be less than or equal to 16.

CDA_POWER_UNIT = 6369289

Specifies the measurement unit of the measured code domain power results.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is dB.

Name (Value)	Description
dB (0)	The CDA measurement results are reported in dB.
dBm (1)	The CDA measurement results are reported in dBm.

CDA_RECEIVE_FILTER_ENABLED = 6369294

Specifies whether to enable the received filter for the code domain analysis (CDA) measurement. Use this attribute to disable the filter, if the received signal is already filtered.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	Disables receive filtering for the CDA measurement.
True (1)	Enables receive filtering for the CDA measurement.

CDA_RESULTS_CHIP_RATE_ERROR = 6369318

Returns the chip rate error. This value is expressed in parts per million (ppm).

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_FREQUENCY_ERROR = 6369317

Returns the frequency error. This value is expressed in Hz.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_IQ_GAIN_IMBALANCE = 6369315

Returns the I/Q gain imbalance of the composite signal averaged over all measured slots. This value is expressed in dB.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_IQ_ORIGIN_OFFSET = 6369314

Returns the I/Q origin offset of the composite signal averaged over all measured slots. This value is expressed in dB.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_IQ_QUADRATURE_ERROR = 6369316

Returns the I/Q quadrature error of the composite signal averaged over all measured slots. This value is expressed in degrees.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_I_MEAN_ACTIVE_POWER = 6369309

Returns the average power of all active code channels measured on the I-branch. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_I_PEAK_INACTIVE_POWER = 6369310

Returns the maximum measured code power among the set of inactive channels on the I-branch and in the code domain of the base spreading factor. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_MEAN_ACTIVE_POWER = 6369305

Returns the average power of all active code channels. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_MEAN_INACTIVE_POWER = 6369307

Returns the average code power, measured among the set of inactive channels, in the code domain of the base spreading factor. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_MEAN_PILOT_POWER = 6369313

Returns the mean power of the R-PICH.

Returns the mean power value in dB, when you set the CDA_POWER_UNIT attribute to dB.

Returns the mean power value in dBm, when you set the CDA Pwr Unit attribute to dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_MEAN_SYMBOL_POWER = 6369302

Returns the mean symbol power of the configured measurement channel. This value is expressed in dB, when you set the CDA_POWER_UNIT attribute to dB, and in dBm, when you set the CDA Pwr Unit attribute to dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_PEAK_ACTIVE_POWER = 6369306

Returns the maximum power among all active code channels. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_PEAK_INACTIVE_POWER = 6369308

Returns the maximum measured code power, measured among the set of inactive channels, in the code domain of the base spreading factor. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_PEAK_SYMBOL_EVM = 6369299

Returns the peak symbol EVM of the configured measurement channel. This value is expressed as a percentage.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_Q_MEAN_ACTIVE_POWER = 6369311

Returns the average power of all active code channels measured on the Q-branch. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_Q_PEAK_INACTIVE_POWER = 6369312

Returns the maximum measured code power among the set of inactive channels on the Q-branch and in the code domain of the base spreading factor. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_RMS_SYMBOL_EVM = 6369298

Returns the RMS symbol EVM of the configured measurement channel. This value is expressed as a percentage.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_RMS_SYMBOL_MAGNITUDE_ERROR = 6369300

Returns the RMS symbol magnitude error of the configured measurement channel. This value is expressed as a percentage.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_RMS_SYMBOL_PHASE_ERROR = 6369301

Returns the RMS symbol phase error of the configured measurement channel. This value is expressed in degrees.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_TOTAL_ACTIVE_POWER = 6369304

Returns the sum of the powers of all active code channels. If you set the CDA_POWER_UNIT attribute to dBm, this measurement returns the absolute measured power; otherwise, this measurement returns a value relative to the CDA_RESULTS_TOTAL_POWER attribute.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_RESULTS_TOTAL_POWER = 6369303

Returns the mean power of the received signal. This value is expressed in dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CDA_SPECTRUM_INVERTED = 6369290

Specifies whether the spectrum of the signal is inverted.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measured spectrum is normal.
True (1)	The measured spectrum is inverted.

CDA_SYNCHRONIZATION_MODE = 6369282

Specifies whether the measurement is performed from the frame, slot, or symbol boundary.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Slot.

Name (Value)	Description
Frame (0)	The frame boundary is detected, and the measurement is performed over the number of slots specified by the CDA Meas Length attribute starting at the CDA measurement offset slots from the frame boundary.
Slot (1)	The slot boundary is detected, and the measurement is performed over the number of slots specified by the CDA Meas Length attribute starting at the CDA measurement offset slots from the slot boundary.
Arbitrary (2)	The symbol boundary is detected, and the measurement is performed over the number of slots specified by the CDA Meas Length attribute starting at the CDA measurement offset slots from the symbol boundary.

CENTER_FREQUENCY = 6291457

Specifies the carrier frequency of the RF signal to acquire. The signal analyzer tunes to this frequency. This value is expressed in Hz.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value of this attribute is hardware dependent.

CHANNEL_CONFIGURATION_MODE = 6291474

Specifies whether to detect the channels automatically or to use a specified channel configuration.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Auto Detect.

Name (Value)	Description
Auto Detect (0)	Specifies that the system automatically detects the channels.
User Defined (1)	Specifies that the system uses a specific channel configuration.

CHP_ALL_TRACES_ENABLED = 6303764

Specifies whether to enable the traces to be stored and retrieved after performing the CHP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

CHP_AVERAGING_COUNT = 6303750

Specifies the number of acquisitions used for averaging when you set the CHP_AVERAGING_ENABLED attribute to True.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10.

CHP_AVERAGING_ENABLED = 6303751

Specifies whether to enable averaging for the CHP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measurement is performed on a single acquisition.
True (1)	The CHP measurement uses the CHP Averaging Count attribute as the number of acquisitions over which the CHP measurement is averaged.

CHP_AVERAGING_TYPE = 6303753

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the CHP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is RMS.

Name (Value)	Description
RMS (0)	The power spectrum is linearly averaged. RMS averaging reduces signal fluctuations but not the noise floor.
Log (1)	The power spectrum is averaged on a logarithmic scale.
Scalar (2)	The square root of the power spectrum is averaged.
Max (3)	The peak power in the spectrum at each frequency bin is retained from one acquisition to the next.
Min (4)	The lowest power in the spectrum at each frequency bin is retained from one acquisition to the next.

CHP_INTEGRATION_BANDWIDTH = 6303746

Returns the CHP carrier integration bandwidth. This value is expressed in Hz.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

CHP_MEASUREMENT_ENABLED = 6303744

Specifies whether to enable the CHP measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

CHP_NUMBER_OF_ANALYSIS_THREADS = 6303747

Specifies the maximum number of threads used for parallelism for the CHP measurement.

The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1.

CHP_RBW_FILTER_AUTO_BANDWIDTH = 6303756

Specifies whether the measurement computes the RBW.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the RBW that you specify in the CHP RBW attribute.
True (1)	The measurement computes the RBW.

CHP_RBW_FILTER_BANDWIDTH = 6303757

Specifies the bandwidth of the RBW filter used to sweep the acquired signal when you set the CHP_RBW_FILTER_AUTO_BANDWIDTH attribute to False. This value is expressed in Hz.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10 kHz.

CHP_RBW_FILTER_TYPE = 6303758

Specifies the shape of the digital RBW filter.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Gaussian.

Name (Value)	Description
FFT Based (0)	No RBW filtering is performed.
Gaussian (1)	An RBW filter with a Gaussian response is applied.
Flat (2)	An RBW filter with a flat response is applied.

CHP_RESULTS_CARRIER_ABSOLUTE_POWER = 6303765

Returns the averaged CHP measured in the specified integration bandwidth. This value is expressed in dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

CHP_SWEEP_TIME_AUTO = 6303761

Specifies whether the measurement computes the sweep time.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the sweep time that you specify in the CHP Sweep Time attribute.
True (1)	The measurement uses the default sweep time of 0.001667 seconds.

CHP_SWEEP_TIME_INTERVAL = 6303762

Specifies the sweep time when you set the CHP_SWEEP_TIME_AUTO attribute to False. This value is expressed in seconds.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.001667 seconds.

DIGITAL_EDGE_TRIGGER_EDGE = 6291462

Specifies the active edge for the trigger. This attribute is used only when you set the TRIGGER_TYPE attribute to Digital Edge.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Rising Edge.

Name (Value)	Description
Rising Edge (0)	The trigger asserts on the rising edge of the signal.
Falling Edge (1)	The trigger asserts on the falling edge of the signal.

DIGITAL_EDGE_TRIGGER_SOURCE = 6291461

Specifies the source terminal for the digital edge trigger. This attribute is used only when you set the TRIGGER_TYPE attribute to Digital Edge.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value of this attribute is hardware dependent.

DOWNLINK_SPREADING_PN_OFFSET = 6291488

Specified the PN offset in increments of 64 chips for forward link.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.

EXTERNAL_ATTENUATION = 6291459

Specifies the attenuation of a switch or cable connected to the RF IN connector of the signal analyzer. This value is expressed in dB. For more information about attenuation, refer to the RF Attenuation and Signal Levels topic for your device in the NI RF Vector Signal Analyzers Help.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0 dB.

IQ_POWER_EDGE_TRIGGER_LEVEL = 6291464

Specifies the power level at which the device triggers. This value is expressed in dB when the IQ_POWER_EDGE_TRIGGER_LEVEL_TYPE attribute is set to Relative and in dBm when the IQ Power Edge Level Type attribute is set to Absolute. The device asserts the trigger when the signal exceeds the level specified by the value of this attribute, taking into consideration the specified slope. This attribute is used only when you set the TRIGGER_TYPE attribute to IQ Power Edge.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value of this attribute is hardware dependent.

IQ_POWER_EDGE_TRIGGER_LEVEL_TYPE = 6295551

Specifies the reference for the IQ Power Edge Level Type attribute. This attribute is used only when you set the TRIGGER_TYPE attribute to IQ Power Edge.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Relative.

Name (Value)	Description
Relative (0)	The IQ Power Edge Level attribute is relative to the value of the Reference Level attribute.
Absolute (1)	The IQ Power Edge Level attribute specifies the absolute power.

IQ_POWER_EDGE_TRIGGER_SLOPE = 6291465

Specifies whether the device asserts the trigger when the signal power is rising or when it is falling. The device asserts the trigger when the signal power exceeds the specified level with the slope you specify. This attribute is used only when you set the TRIGGER_TYPE attribute to IQ Power Edge.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Rising Slope.

Name (Value)	Description
Rising Slope (0)	The trigger asserts when the signal power is rising.
Falling Slope (1)	The trigger asserts when the signal power is falling.

IQ_POWER_EDGE_TRIGGER_SOURCE = 6291463

Specifies the channel from which the device monitors the trigger. This attribute is used only when you set the TRIGGER_TYPE attribute to IQ Power Edge.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value of this attribute is hardware dependent.

LIMITED_CONFIGURATION_CHANGE = 6344707

Specifies the set of attributes that are considered by RFmx in the locked signal configuration state.

If your test system performs the same measurement at different selected ports, multiple frequencies and/or power levels repeatedly, enabling this attribute can help achieve faster measurements. When you set this attribute to a value other than Disabled, the RFmx driver will use an optimized code path and skip some checks. Because RFmx skips some checks when you use this attribute, you need to be aware of the limitations of this feature, which are listed in the Limitations of the Limited Configuration Change Property topic.

You can also use this attribute to lock a specific instrument configuration for a signal so that every time that you initiate the signal, RFmx applies the RFmxInstr attributes from a locked configuration.

NI recommends you use this attribute in conjunction with named signal configurations. Create named signal configurations for each measurement configuration in your test program and set this attribute to a value other than Disabled for one or more of the named signal configurations. This allows RFmx to precompute the acquisition settings for your measurement configurations and re-use the precomputed settings each time you initiate the measurement. You do not need to use this attribute if you create named signals for all the measurement configurations in your test program during test sequence initialization and do not change any RFInstr or personality attributes while testing each device under test. RFmx automatically optimizes that use case.

Specify the named signal configuration you are setting this attribute in the selector string input. You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Disabled.

Name (Value)	Description
Disabled (0)	This is the normal mode of RFmx operation. All configuration changes in RFmxInstr attributes or in personality attributes will be applied during RFmx Commit.
No Change (1)	Signal configuration is locked after the first Commit of the named signal configuration. Any configuration change thereafter either in RFmxInstr attributes or personality attributes will not be considered by subsequent RFmx Commits or Initiates of this signal. Use No Change if you have created named signal configurations for all measurement configurations but are setting some RFmxInstr attributes. Refer to the Limitations of the Limited Configuration Change Property topic for more details about the limitations of using this mode.
Frequency (2)	Signal configuration, other than center frequency and external attenuation, is locked after first Commit of the named signal configuration. Thereafter, only the Center Frequency and External Attenuation attribute value changes will be considered by subsequent driver Commits or Initiates of this signal. Refer to the Limitations of the Limited Configuration Change Property topic for more details about the limitations of using this mode.
Reference Level (3)	Signal configuration, other than the reference level, is locked after first Commit of the named signal configuration. Thereafter only the Reference Level attribute value change will be considered by subsequent driver Commits or Initiates of this signal. If you have configured this signal to use an IQ Power Edge Trigger, NI recommends that you set the IQ Power Edge Level Type to Relative so that the trigger level is automatically adjusted as you adjust the reference level. Refer to the Limitations of the Limited Configuration Change Property topic for more details about the limitations of using this mode.
Freq and Ref Level (4)	Signal configuration, other than center frequency, reference level, and external attenuation, is locked after first Commit of the named signal configuration. Thereafter only Center Frequency, Reference Level, and External Attenuation attribute value changes will be considered by subsequent driver Commits or Initiates of this signal. If you have configured this signal to use an IQ Power Edge Trigger, NI recommends you set the IQ Power Edge Level Type to Relative so that the trigger level is automatically adjusted as you adjust the reference level. Refer to the Limitations of the Limited Configuration Change Property topic for more details about the limitations of using this mode.
Selected Ports, Freq and Ref Level (5)	Signal configuration, other than selected ports, center frequency, reference level, external attenuation, and RFInstr configuration, is locked after first Commit or Initiate of the named signal configuration. Thereafter only Selected Ports, Center Frequency, Reference Level, and External Attenuation attribute value changes will be considered by subsequent driver Commits or Initiates of this signal. If you have configured this signal to use an IQ Power Edge Trigger, NI recommends you set the IQ Power Edge Level Type to Relative so that the trigger level is automatically adjusted as you adjust the reference level. Refer to the Limitations of the Limited Configuration Change Property topic for more details about the limitations of using this mode.

LINK_DIRECTION = 6291469

Specifies the link direction of the received signal.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Uplink.

Name (Value)	Description
Downlink (0)	CDMA2k measurement uses 3GPP CDMA2k forward link direction also known as downlink direction to measure the received signal.
Uplink (1)	CDMA2k measurement uses 3GPP CDMA2k reverse link direction also known as uplink direction to measure the received signal.

MODACC_ALL_TRACES_ENABLED = 6361109

Specifies whether to enable the traces to be stored and retrieved after performing the modulation accuracy (ModAcc) measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

MODACC_IQ_GAIN_IMBALANCE_REMOVAL_ENABLED = 6361249

Specifies whether to remove the I/Q gain imbalance before an EVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q gain imbalance is not removed before the EVM measurement.
True (1)	I/Q gain imbalance is removed before the EVM measurement.

MODACC_IQ_OFFSET_REMOVAL_ENABLED = 6361096

Specifies whether to remove the I/Q offset before an EVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q offset is not removed before the EVM measurement.
True (1)	I/Q offset is removed before the EVM measurement.

MODACC_IQ_QUADRATURE_ERROR_REMOVAL_ENABLED = 6361250

Specifies whether to remove the I/Q quadrature error before an EVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q quadrature error is not removed before the EVM measurement.
True (1)	I/Q quadrature error is removed before the EVM measurement.

MODACC_MEASUREMENT_ENABLED = 6361088

Specifies whether to enable the modulation accuracy (ModAcc) measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

MODACC_MEASUREMENT_LENGTH = 6361095

Specifies the duration of the modulation accuracy (ModAcc) measurement. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1. The valid values are 1 to 16, inclusive. The sum of the ModAcc measurement offset and the ModAcc measurement length must be less than or equal to 16.

MODACC_MEASUREMENT_OFFSET = 6361094

Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the MODACC_SYNCHRONIZATION_MODE attribute. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0. The valid values are 1 to 16, inclusive. The sum of the ModAcc measurement offset and the ModAcc measurement length must be less than or equal to 16.

MODACC_MULTI_CARRIER_FILTER_ENABLED = 6361104

Specifies whether to enable the multi carrier filter which can be used to improve ModAcc measurement quality in presence of neighboring carriers.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	Disables multi carrier filter for ModAcc measurement.
True (1)	Enables multi carrier filter for ModAcc measurement.

MODACC_RECEIVE_FILTER_ENABLED = 6361251

Specifies whether to enable the received filter for the ModAcc measurement. For RC1/2, this attribute refers to the band-limiting filter specified in the Chapter 6.4.2.1 of 3GPP2 C.S0011-E. For RC3/4, this attribute refers to the complementary filter specified in the Chapter 6.4.2.2 of 3GPP2 C.S0011-E.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	Disables received filtering for the ModAcc measurement.
True (1)	Enables received filtering for the ModAcc measurement.

MODACC_RESULTS_CHIP_RATE_ERROR = 6361139

Returns the chip rate error. This value is expressed in parts per million (ppm).

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_DETECTED_BRANCH = 6361143

Returns the branch of the detected channel. If you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined, the attribute returns the branch of the configured channel.

Use “channel< <format type=”monospace-italic”>n</format> >” as the Selector String to read this attribute.

Name (Value)	Description
I (0)	The signal modulated on the in-phase branch.
Q (1)	The signal modulated on the quadrature branch.
I and Q (2)	The signal modulated on the in-phase branch and quadrature branch.

MODACC_RESULTS_DETECTED_WALSH_CODE_LENGTH = 6361141

Returns the Walsh code length of the detected channel. If you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined, the attribute returns the Walsh code length of the configured channel.

Use “channel< <format type=”monospace-italic”>n</format> >” as the Selector String to read this attribute.

MODACC_RESULTS_DETECTED_WALSH_CODE_NUMBER = 6361142

Returns the Walsh code number of the detected channel. If you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined, the attribute returns the Walsh code number of the configured channel.

Use “channel< <format type=”monospace-italic”>n</format> >” as the Selector String to read this attribute.

MODACC_RESULTS_FREQUENCY_ERROR = 6361127

Returns the frequency error averaged over all measured slots. This value is expressed in Hz.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_IQ_GAIN_IMBALANCE = 6361125

Returns the I/Q gain imbalance of the composite signal averaged over all measured slots. This value is expressed in dB.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_IQ_ORIGIN_OFFSET = 6361124

Returns the I/Q origin offset of the composite signal averaged over all measured slots. This value is expressed in dB.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_IQ_QUADRATURE_ERROR = 6361126

Returns the I/Q quadrature error of the composite signal, averaged over all measured slots. This value is expressed in degrees.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_NUMBER_OF_DETECTED_CHANNELS = 6361140

Returns the total number of detected channels. If you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined, the attribute returns the number of configured channels.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_PEAK_ACTIVE_CDE = 6361132

Returns the maximum value among the code domain errors (CDEs) for all active channels. This value is expressed in dB. The active CDEs are computed by projecting the descrambled error vector onto the codes of each active channel. The active CDE is defined as the ratio of the mean power of the projection onto that code to the mean power of the composite reference waveform.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_PEAK_ACTIVE_CDE_BRANCH = 6361145

Returns the branch of the channel corresponding to the value that the MODACC_RESULTS_PEAK_ACTIVE_CDE attribute returns.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

Name (Value)	Description
I (0)	The signal is modulated on the in-phase branch.
Q (1)	The signal is modulated on the quadrature branch.
I and Q (2)	Complex modulated signal.

MODACC_RESULTS_PEAK_ACTIVE_CDE_WALSH_CODE_LENGTH = 6361133

Returns the Walsh code length of the channel corresponding to the value that the MODACC_RESULTS_PEAK_ACTIVE_CDE attribute returns.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_PEAK_ACTIVE_CDE_WALSH_CODE_NUMBER = 6361135

Returns the Walsh code number of the channel corresponding to the value that the MODACC_RESULTS_PEAK_ACTIVE_CDE attribute returns.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_PEAK_CDE = 6361129

Returns the maximum value among the code domain errors (CDEs). This value is expressed in dB. The CDEs are computed by projecting the descrambled error vector onto the code domain at a specific spreading factor. The CDE for every code with a specific spreading factor is defined as the ratio of the mean power of the projection onto that code to the mean power of the composite reference waveform. A fixed spreading factor of 16 is used. The CDEs are computed separately for I and Q branches.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_PEAK_CDE_BRANCH = 6361144

Returns the branch corresponding to the value that the MODACC_RESULTS_PEAK_ACTIVE_CDE attribute returns.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

Name (Value)	Description
I (0)	The signal is modulated on the in-phase branch.
Q (1)	The signal is modulated on the quadrature branch.
I and Q (2)	Complex modulated signal.

MODACC_RESULTS_PEAK_CDE_WALSH_CODE_NUMBER = 6361131

Returns the Walsh code number corresponding to the value that the MODACC_RESULTS_PEAK_CDE attribute returns.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_PEAK_EVM = 6361121

Returns the peak EVM of the composite signal. This value is expressed as a percentage.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_RHO = 6361128

Returns the correlation of the received signal with the reference signal normalized by the signal power. The value of Rho is between 0 and 1.0, inclusive. A value of 1.0 indicates that the received signal and the reference signal are perfectly correlated.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_RMS_EVM = 6361120

Returns the RMS EVM of the composite signal. This value is expressed as a percentage.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_RMS_MAGNITUDE_ERROR = 6361122

Returns the RMS magnitude error of the composite signal. This value is expressed as a percentage.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_RMS_PHASE_ERROR = 6361123

Returns the RMS phase error of the composite signal. This value is expressed in degrees.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_RESULTS_SLOT_TIMING_ERROR = 6361136

Returns the measured timing error from the beginning of the acquisition to the location of the first slot acquired. This value is expressed in seconds.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

MODACC_SPECTRUM_INVERTED = 6361097

Specifies whether the spectrum of the signal is inverted.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measured spectrum is not inverted.
True (1)	The measured spectrum is inverted.

MODACC_SYNCHRONIZATION_MODE = 6361093

Specifies whether the measurement is performed from the frame, slot, or symbol boundary.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Slot.

Name (Value)	Description
Frame (0)	The frame boundary is detected, and the measurement is performed over the ModAcc Meas Length attribute starting at the ModAcc Meas Offset attribute from the frame boundary.
Slot (1)	The slot boundary is detected, and the measurement is performed over the ModAcc Meas Length attribute starting at the ModAcc Meas Offset attribute from the slot boundary.
Arbitrary (2)	The symbol boundary is detected, and the measurement is performed over the ModAcc Meas Length attribute starting at the ModAcc Meas Offset attribute from the slot boundary.

NUMBER_OF_CHANNELS = 6291478

Specifies the number of user-defined channels. This attribute is used only when you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.

OBW_ALL_TRACES_ENABLED = 6316050

Specifies whether to enable the traces to be stored and retrieved after performing the OBW.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

OBW_AVERAGING_COUNT = 6316038

Specifies the number of acquisitions used for averaging when you set the OBW_AVERAGING_ENABLED attribute to True.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10.

OBW_AVERAGING_ENABLED = 6316039

Specifies whether to enable averaging for the OBW measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measurement is performed on a single acquisition.
True (1)	The OBW measurement uses the value of the OBW Averaging Count attribute as the number of acquisitions over which the OBW measurement is averaged.

OBW_AVERAGING_TYPE = 6316041

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the OBW measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is RMS.

Name (Value)	Description
RMS (0)	The power spectrum is linearly averaged. RMS averaging reduces signal fluctuations but not the noise floor.
Log (1)	The power spectrum is averaged in a logarithmic scale.
Scalar (2)	The square root of the power spectrum is averaged.
Max (3)	The peak power in the spectrum at each frequency bin is retained from one acquisition to the next.
Min (4)	The lowest power in the spectrum at each frequency bin is retained from one acquisition to the next.

OBW_MEASUREMENT_ENABLED = 6316032

Specifies whether to enable the OBW measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

OBW_NUMBER_OF_ANALYSIS_THREADS = 6316035

Specifies the maximum number of threads used for parallelism for the OBW measurement.

The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1.

OBW_RBW_FILTER_AUTO_BANDWIDTH = 6316044

Specifies whether the measurement computes the RBW.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the RBW that you specify in the OBW RBW attribute.
True (1)	The measurement computes the RBW.

OBW_RBW_FILTER_BANDWIDTH = 6316045

Specifies the bandwidth of the RBW filter used to sweep the acquired signal when you set the OBW_RBW_FILTER_AUTO_BANDWIDTH attribute to False. This value is expressed in Hz.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 30 kHz.

OBW_RBW_FILTER_TYPE = 6316046

Specifies the shape of the digital RBW filter.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Gaussian.

Name (Value)	Description
FFT Based (0)	No RBW filtering is performed.
Gaussian (1)	An RBW filter with a Gaussian response is applied.
Flat (2)	An RBW filter with a Flat response is applied.

OBW_RESULTS_ABSOLUTE_POWER = 6316052

Returns the absolute power measured in the OBW. This value is expressed in dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

OBW_RESULTS_OCCUPIED_BANDWIDTH = 6316051

Returns the bandwidth that occupies 99% of the total signal power. This value is expressed in Hz.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

OBW_RESULTS_START_FREQUENCY = 6316053

Returns the start frequency of the OBW. This value is expressed in Hz.

The OBW is calculated using the following formula: OBW = Stop Frequency - Start Frequency

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

OBW_RESULTS_STOP_FREQUENCY = 6316054

Returns the stop frequency of the OBW. This value is expressed in Hz.

The OBW is calculated using the following formula: OBW = Stop Frequency - Start Frequency

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

OBW_SPAN = 6316036

Returns the frequency span of the OBW measurement. This value is expressed in Hz.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

OBW_SWEEP_TIME_AUTO = 6316047

Specifies whether the measurement computes the sweep time.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the sweep time that you specify in the OBW Sweep Time attribute.
True (1)	The measurement uses the default sweep time of 0.001667 seconds.

OBW_SWEEP_TIME_INTERVAL = 6316048

Specifies the sweep time when you set the OBW_SWEEP_TIME_AUTO attribute to False. This value is expressed in seconds.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.001667 seconds.

QEVM_ALL_TRACES_ENABLED = 6365194

Specifies whether to enable the traces to be stored and retrieved after performing the QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

QEVM_AVERAGING_COUNT = 6365188

Specifies the number of measurements used for averaging when you set the QEVM_AVERAGING_ENABLED attribute to True.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default values is 10. The valid values are 1 to 10000, inclusive.

QEVM_AVERAGING_ENABLED = 6365187

Specifies whether to enable averaging for the QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The averaging is disabled for the measurement.
True (1)	The averaging is enabled for the measurement.

QEVM_IQ_GAIN_IMBALANCE_REMOVAL_ENABLED = 6365191

Specifies whether to remove I/Q gain imbalance before QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q gain imbalance is not removed before the QEVM measurement.
True (1)	I/Q gain imbalance is removed before the QEVM measurement.

QEVM_IQ_OFFSET_REMOVAL_ENABLED = 6365190

Specifies whether to remove I/Q offset before QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q offset is not removed before the QEVM measurement.
True (1)	I/Q offset is removed before the QEVM measurement.

QEVM_IQ_QUADRATURE_ERROR_REMOVAL_ENABLED = 6365192

Specifies whether to remove I/Q quadrature error before QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	I/Q quadrature error is not removed before the QEVM measurement.
True (1)	I/Q quadrature error is removed before the QEVM measurement.

QEVM_MEASUREMENT_ENABLED = 6365184

Specifies whether to enable the QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

QEVM_MEASUREMENT_LENGTH = 6365186

Specifies the number of chips used for a single measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1536. The valid values are 700 to 2500, inclusive.

QEVM_NUMBER_OF_ANALYSIS_THREADS = 6365195

Specifies the maximum number of threads used for parallelism for the QEVM measurement.

The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations.

The default value is 1. Valid values range from 0 to 10, inclusive.

QEVM_RECEIVE_FILTER_ENABLED = 6365193

Specifies whether to enable the received filter for the QEVM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	Disables received filtering for the QEVM measurement.
True (1)	Enables received filtering for the QEVM measurement.

QEVM_RESULTS_MAXIMUM_CHIP_RATE_ERROR = 6365214

Returns the maximum chip rate error. This value is expressed in parts per million (ppm).

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_FREQUENCY_ERROR = 6365206

Returns the maximum frequency error of the received signal. This value is expressed in Hz.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_IQ_GAIN_IMBALANCE = 6365210

Returns the maximum I/Q gain imbalance of the received signal. This value is expressed in dB.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_IQ_ORIGIN_OFFSET = 6365208

Returns the maximum origin offset of the received signal. This value is expressed in dB.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_IQ_QUADRATURE_ERROR = 6365212

Returns the maximum I/Q quadrature error (phase imbalance) of the received signal. This value is expressed in degrees.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_MAGNITUDE_ERROR = 6365202

Returns the maximum magnitude error of the received signal. This value is expressed as a percentage.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_PEAK_EVM = 6365200

Returns the maximum peak EVM of the received signal. This value is expressed as a percentage.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_PHASE_ERROR = 6365204

Returns the maximum phase error of the received signal. This value is expressed in degrees.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MAXIMUM_RMS_EVM = 6365198

Returns the maximum RMS EVM of the received signal. This value is expressed as a percentage.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_CHIP_RATE_ERROR = 6365213

Returns the mean chip rate error. This value is expressed in parts per million (ppm).

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_FREQUENCY_ERROR = 6365205

Returns the mean averaged frequency error of the received signal. This value is expressed in Hz.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_IQ_GAIN_IMBALANCE = 6365209

Returns the mean I/Q gain imbalance of the received signal. This value is expressed in dB.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_IQ_ORIGIN_OFFSET = 6365207

Returns the mean averaged origin offset of the received signal. This value is expressed in dB.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_IQ_QUADRATURE_ERROR = 6365211

Returns the mean I/Q quadrature error (phase imbalance) of the received signal. This value is expressed in degrees.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_MAGNITUDE_ERROR = 6365201

Returns the mean averaged magnitude error of the received signal. This value is expressed as a percentage.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_PEAK_EVM = 6365199

Returns the mean averaged peak EVM of the received signal. This value is expressed as a percentage.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_PHASE_ERROR = 6365203

Returns the mean averaged phase error of the received signal. This value is expressed in degrees.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the `Selector String <https://www.ni.com/docs/en-US/bundle/rfmx/page/selector-strings-net.html>`_s topic for information about the string syntax for named signals.

QEVM_RESULTS_MEAN_RMS_EVM = 6365197

Returns the mean averaged RMS EVM of the received signal. This value is expressed as a percentage.

You do not need to use a selector string to read this attribute for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals.

QEVM_SPECTRUM_INVERTED = 6365189

Specifies whether the spectrum of the signal is inverted.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measurement spectrum is normal.
True (1)	The measurement spectrum is inverted.

RADIO_CONFIGURATION = 6291473

Specifies the radio configuration for the channel.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is RC3.

Name (Value)	Description
RC1 (0)	If Link Direction attribute is set to Uplink, Radio configuration 1 includes 64-ary orthogonal modulation, reverse fundamental channel (R-FCH), and reverse supplemental code channels (R-SCCHs). If Link Direction attribute is set to Downlink, Radio Configuration 1 includes binary phase-shift keying (BPSK), forward fundamental channels (F-FCHs) and forward supplemental channels (F-SCHs).
RC2 (1)	If Link Direction attribute is set to Uplink, Radio configuration 2 includes 64-ary orthogonal modulation, R-FCH, and R-SCCHs. If Link Direction attribute is set to Downlink, Radio Configuration 2 includes BPSKs, F-FCHs and F-SCHs.
RC3 (2)	If Link Direction attribute is set to Uplink, Radio configuration 3 includes BPSK, R-FCH, and reverse supplemental channels (R-SCHs). If Link Direction attribute is set to Downlink, Radio Configuration 3 includes quadrature phase-shift keying (QPSK), F-FCHs and F-SCHs.
RC4 (3)	If Link Direction attribute is set to Uplink, Radio configuration 4 includes BPSK, R-FCH, and R-SCHs. If Link Direction attribute is set to Downlink, Radio Configuration 4 includes QPSK, F-FCHs and F-SCHs.
RC5 (4)	If Link Direction attribute is set to Uplink, Radio configuration 5 is not supported and gives invalid results. If Link Direction attribute is set to Downlink, Radio Configuration 5 includes QPSK, F-FCHs and F-SCHs.

REFERENCE_LEVEL = 6291458

Specifies the reference level, which represents the maximum expected power of the RF input signal. This value is expressed in dBm for RF devices and V_pk-pkfor baseband devices.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value of this attribute is hardware dependent.

REFERENCE_LEVEL_HEADROOM = 6295548

Specifies the margin RFmx adds to the REFERENCE_LEVEL attribute. The margin avoids clipping and overflow warnings if the input signal exceeds the configured reference level.

RFmx configures the input gain to avoid clipping and associated overflow warnings provided the instantaneous power of the input signal remains within the Reference Level plus the Reference Level Headroom. If you know the input power of the signal precisely or previously included the margin in the Reference Level, you could improve the signal-to-noise ratio by reducing the Reference Level Headroom.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

Supported devices: PXIe-5668R, PXIe-5830/5831/5832/5840/5841/5842/5860.

Default values

Name (value)	Description
PXIe-5668	6 dB
PXIe-5830/5831/5832/5841/5842/5860	1 dB
PXIe-5840	0 dB

RESULT_FETCH_TIMEOUT = 6340608

Specifies the time to wait before results are available in the RFmxCDMA2k Attribute. This value is expressed in seconds.

Set this value to a time longer than expected for fetching the measurement. A value of -1 specifies that the RFmxCDMA2k Attribute waits until the measurement is complete before fetching the measurement.

The default value is 10 seconds.

SELECTED_PORTS = 6295549

Specifies the instrument port to be configured to acquire a signal. Use nirfmxinstr.session.Session.get_available_ports() method to get the valid port names.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

Valid values

Name (value)	Description
PXIe-5830	if0, if1
PXIe-5831/5832	if0, if1, rf<0-1>/port<x>, where 0-1 indicates one (0) or two (1) mmRH-5582 connections and x is the port number on the mmRH-5582 front panel
Other devices	“” (empty string)

Default values

Name (value)	Description
PXIe-5830/5831/5832	if1
Other devices	“” (empty string)

SEM_ALL_TRACES_ENABLED = 6324263

Specifies whether to enable the traces to be stored and retrieved after performing the SEM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

SEM_AVERAGING_COUNT = 6324254

Specifies the number of acquisitions used for averaging when you set the SEM_AVERAGING_ENABLED attribute to True.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 10.

SEM_AVERAGING_ENABLED = 6324255

Specifies whether to enable averaging for the SEM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measurement is performed on a single acquisition.
True (1)	The SEM measurement uses the value of the SEM Averaging Count attribute as the number of acquisitions over which the SEM measurement is averaged.

SEM_AVERAGING_TYPE = 6324257

Specifies the averaging type for averaging multiple spectrum acquisitions. The averaged spectrum is used for the SEM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is RMS.

Name (Value)	Description
RMS (0)	The power spectrum is linearly averaged. RMS averaging reduces signal fluctuations but not the noise floor.
Log (1)	The power spectrum is averaged in a logarithmic scale.
Scalar (2)	The square root of the power spectrum is averaged.
Max (3)	The peak power in the spectrum at each frequency bin is retained from one acquisition to the next.
Min (4)	The least power in the spectrum at each frequency bin is retained from one acquisition to the next.

SEM_CARRIER_INTEGRATION_BANDWIDTH = 6324229

Returns the SEM carrier integration bandwidth. This value is expressed in Hz.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

SEM_MEASUREMENT_ENABLED = 6324224

Specifies whether to enable the SEM measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

SEM_NUMBER_OF_ANALYSIS_THREADS = 6324253

Specifies the maximum number of threads used for parallelism for the SEM measurement.

The number of threads can range from 1 to the number of physical cores. The number of threads you set may not be used in calculations. The actual number of threads used depends on the problem size, system resources, data availability, and other considerations.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 1.

SEM_NUMBER_OF_OFFSETS = 6324235

Returns the number of SEM offset segments.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

SEM_OFFSET_BANDWIDTH_INTEGRAL = 6324236

Returns the bandwidth integral for a specific offset segment.

A bandwidth integral greater than 1 indicates a RBW filter of a narrower bandwidth is used for the offset segment measurement, and digital processing is used to achieve the RBW defined for the offset segment.

Use the following equation to calculate the value of the offset segment RBW: offset segment RBW = RBW * BW integral

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_OFFSET_RBW_FILTER_BANDWIDTH = 6324247

Returns the bandwidth of the RBW filter used to sweep the offset segment. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_OFFSET_RBW_FILTER_TYPE = 6324248

Returns the type of RBW filter used to sweep the offset segment.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

The default value is Gaussian.

Name (Value)	Description
FFT Based (0)	No RBW filtering is performed.
Gaussian (1)	The RBW filter has a Gaussian response.
Flat (2)	The RBW filter has a flat response.
Synch Tuned - 4 (3)	The RBW filter has a response of a 4-pole synchronously tuned filter.
Synch Tuned - 5 (4)	The RBW filter has a response of a 5-pole synchronously tuned filter.

SEM_OFFSET_START_FREQUENCY = 6324244

Returns the start frequency of an SEM offset segment relative to the carrier frequency. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_OFFSET_STOP_FREQUENCY = 6324245

Returns the stop frequency of an SEM offset segment relative to the carrier frequency. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_CARRIER_ABSOLUTE_INTEGRATED_POWER = 6324269

Returns the carrier power. The carrier power is the power centered at the center frequency and integrated over the carrier bandwidth of 1.23 MHz. This value is expressed in dBm.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

SEM_RESULTS_LOWER_OFFSET_ABSOLUTE_INTEGRATED_POWER = 6324276

Returns the absolute power measured in the lower (negative) offset segment. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_ABSOLUTE_PEAK_POWER = 6324278

Returns the peak power measured in the lower (negative) offset segment. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_MARGIN = 6324281

Returns the margin from the limit mask value specified by the standard. This value is expressed in dB. Margin is defined as the minimum difference between the spectrum and the closest limit mask, which can be absolute or relative.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

Setting Specified by the Standard	Margin Description
Absolute	Returns the margin with reference to the absolute limit mask.
Relative	Returns the margin with reference to the relative limit mask.
Abs AND Rel	Returns the margin as the maximum of the margin referenced to the absolute and relative limit masks.
Abs OR Rel	Returns the margin as the minimum of the margin referenced to the absolute and relative limit masks.

SEM_RESULTS_LOWER_OFFSET_MARGIN_ABSOLUTE_POWER = 6324282

Returns the absolute power at which the margin occurred in the lower (negative) offset segment. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_MARGIN_FREQUENCY = 6324284

Returns the frequency at which the margin occurred in the lower (negative) offset segment. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_MARGIN_RELATIVE_POWER = 6324283

Returns the power at which the margin occurred in the lower (negative) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_MEASUREMENT_STATUS = 6324285

Indicates the lower offset segment measurement status based on measurement limits specified by the standard.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

Name (Value)	Description
Fail (0)	The lower offset segment measurement fails according to the measurement limits specified by the standard.
Pass (1)	The lower offset segment measurement passes according to the measurement limits specified by the standard.

SEM_RESULTS_LOWER_OFFSET_PEAK_FREQUENCY = 6324280

Returns the frequency at which the peak power occurred in the lower offset segment. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_RELATIVE_INTEGRATED_POWER = 6324277

Returns the power measured in the lower (negative) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_LOWER_OFFSET_RELATIVE_PEAK_POWER = 6324279

Returns the peak power measured in the lower (negative) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_MEASUREMENT_STATUS = 6324265

Indicates the overall measurement status based on the measurement limits, which are specified by the standard for each offset segment.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

Name (Value)	Description
Fail (0)	The measurement fails according to the measurement limits specified by this standard.
Pass (1)	The measurement passes according to the measurement limits specified by this standard.

SEM_RESULTS_UPPER_OFFSET_ABSOLUTE_INTEGRATED_POWER = 6324289

Returns the power measured in the upper (positive) offset segment. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_ABSOLUTE_PEAK_POWER = 6324291

Returns the peak power measured in the upper (positive) offset segment. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_MARGIN = 6324294

Returns the margin from the limit mask value specified by the standard. This value is expressed in dB. Margin is defined as the minimum difference between the spectrum and the closest limit mask (absolute or relative).

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

Setting Specified by the Standard	Margin Description
Absolute	Returns the margin with reference to the absolute limit mask.
Relative	Returns the margin with reference to the relative limit mask.
Abs AND Rel	Returns the margin as the maximum of the margin referenced to the absolute and relative limit masks.
Abs OR Rel	Returns the margin as the minimum of the margin referenced to the absolute and relative limit masks.

SEM_RESULTS_UPPER_OFFSET_MARGIN_ABSOLUTE_POWER = 6324295

Returns the power at which the margin occurred in the upper (positive) offset segment. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_MARGIN_FREQUENCY = 6324297

Returns the frequency at which the margin occurred in the upper (positive) offset. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_MARGIN_RELATIVE_POWER = 6324296

Returns the power at which the margin occurred in the upper (positive) offset segment. This value is expressed in dBm.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_MEASUREMENT_STATUS = 6324298

Indicates the upper offset measurement status based on measurement limits set by the standard.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

Name (Value)	Description
Fail (0)	The lower offset segment measurement fails according to the measurement limits specified by this standard.
Pass (1)	The lower offset segment measurement passes according to the measurement limits specified by this standard.

SEM_RESULTS_UPPER_OFFSET_PEAK_FREQUENCY = 6324293

Returns the frequency at which the peak power occurred in the upper offset segment. This value is expressed in Hz.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_RELATIVE_INTEGRATED_POWER = 6324290

Returns the power measured in the upper (positive) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_RESULTS_UPPER_OFFSET_RELATIVE_PEAK_POWER = 6324292

Returns the peak power measured in the upper (positive) offset segment relative to the carrier absolute integrated power. This value is expressed in dB.

Use “offset< <format type=”monospace-italic”>n</format> >” as the Selector String to read this result.

SEM_SWEEP_TIME_AUTO = 6324261

Specifies whether the measurement computes the sweep time.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	The measurement uses the sweep time that you specify in the SEM Sweep Time attribute.
True (1)	The measurement uses the default sweep time, 0.001667 seconds.

SEM_SWEEP_TIME_INTERVAL = 6324262

Specifies the sweep time when you set the SEM_SWEEP_TIME_AUTO attribute to False. This value is expressed in seconds.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.001667 seconds.

SLOTPHASE_ALL_TRACES_ENABLED = 6377480

Specifies whether to enable the traces to be stored and retrieved after performing the SlotPhase measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

SLOTPHASE_MEASUREMENT_ENABLED = 6377472

Specifies whether to enable the SlotPhase measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

SLOTPHASE_MEASUREMENT_LENGTH = 6377476

Specifies the duration of the SlotPhase measurement. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 16.

SLOTPHASE_MEASUREMENT_OFFSET = 6377475

Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the SLOTPHASE_SYNCHRONIZATION_MODE attribute. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.

SLOTPHASE_RECEIVE_FILTER_ENABLED = 6377478

Specifies whether to enable the received filter for the SlotPhase measurement. Use this attribute to disable the filter, if the received signal is already filtered.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	Disables received filtering for the SlotPhase measurement.
True (1)	Enables received filtering for the SlotPhase measurement.

SLOTPHASE_RESULTS_MAXIMUM_PHASE_DISCONTINUITY = 6377483

Returns the maximum slot phase discontinuity value observed in the measurement interval. This value is expressed in degrees.

You do not need to use a selector string to read this result for the default signal and result instance. Refer to the Selector String topic for information about the string syntax for named signals and named results.

SLOTPHASE_SPECTRUM_INVERTED = 6377477

Specifies whether the spectrum of the signal is inverted.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measured spectrum is not inverted.
True (1)	The measured spectrum is inverted.

SLOTPHASE_SYNCHRONIZATION_MODE = 6377474

Specifies whether the measurement is performed from the frame or slot boundary.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Slot.

Name (Value)	Description
Frame (0)	The frame boundary is detected, and the measurement is performed over the number of slots specified by the SlotPhase Meas Length attribute starting at the SlotPhase measurement offset slots from the frame boundary.
Slot (1)	The slot boundary is detected, and the measurement is performed over the number of slots specified by the SlotPhase Meas Length attribute starting at the SlotPhase measurement offset slots from the slot boundary.

SLOTPHASE_TRANSIENT_DURATION = 6377479

Specifies the region to exclude for computing the individual slot phase discontinuity values. This value is expressed in seconds.

The transient duration is applied equally on either side of a slot boundary, that is at the start and end of each slot. If you set the transient duration to zero, there is no transient period and the entire slot data is used to determine the phase error best fit line which is used to compute the phase discontinuity at the slot boundaries.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0. The valid values are 0 to 0.0002, inclusive.

SLOTPOWER_MEASUREMENT_ENABLED = 6373376

Specifies whether to enable the SlotPower measurement.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is FALSE.

SLOTPOWER_MEASUREMENT_LENGTH = 6373380

Specifies the duration of the SlotPower measurement. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 16.

SLOTPOWER_MEASUREMENT_OFFSET = 6373379

Specifies the measurement offset to skip from the synchronization boundary. The synchronization boundary is specified by the SLOTPOWER_SYNCHRONIZATION_MODE attribute. This value is expressed in slots.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.

SLOTPOWER_RECEIVE_FILTER_ENABLED = 6373382

Specifies whether to enable the received filter for the SlotPower measurement. Use this attribute to disable the filter, if the received signal is already filtered.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is True.

Name (Value)	Description
False (0)	Disables received filtering for the SlotPower measurement.
True (1)	Enables received filtering for the SlotPower measurement.

SLOTPOWER_SPECTRUM_INVERTED = 6373381

Specifies whether the spectrum of the signal is inverted.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is False.

Name (Value)	Description
False (0)	The measurement spectrum is normal.
True (1)	The measurement spectrum is inverted.

SLOTPOWER_SYNCHRONIZATION_MODE = 6373378

Specifies whether the measurement is performed from the frame or slot boundary.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Slot.

Name (Value)	Description
Frame (0)	The frame boundary is detected, and the measurement is performed over the number of slots specified by the SlotPower Meas Length attribute starting at the SlotPower measurement offset slots from the frame boundary.
Slot (1)	The slot boundary is detected, and the measurement is performed over the number of slots specified by the SlotPower Meas Length attribute starting at the SlotPower measurement offset slots from the slot boundary.

TRIGGER_DELAY = 6291466

Specifies the trigger delay time. This value is expressed in seconds.

If the delay is negative, the measurement acquires pretrigger samples. If the delay is positive, the measurement acquires post-trigger samples.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0 seconds.

TRIGGER_MINIMUM_QUIET_TIME_DURATION = 6291468

Specifies the time duration for which the signal must be quiet before the signal analyzer arms the I/Q power edge trigger. This value is expressed in seconds.

If you set the IQ_POWER_EDGE_TRIGGER_SLOPE attribute to Rising Slope, the signal is quiet below the trigger level. If you set the IQ Power Edge Slope attribute to Falling Slope, the signal is quiet above the trigger level.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value of this attribute is hardware dependent.

TRIGGER_MINIMUM_QUIET_TIME_MODE = 6291467

Specifies whether the measurement computes the minimum quiet time used for triggering.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is Auto.

Name (Value)	Description
Manual (0)	The minimum quiet time for triggering is the value of the Trigger Min Quiet Time attribute.
Auto (1)	The measurement computes the minimum quiet time used for triggering.

TRIGGER_TYPE = 6291460

Specifies the trigger type.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is None.

Name (Value)	Description
None (0)	No Reference Trigger is configured.
Digital Edge (1)	The Reference Trigger is not asserted until a digital edge is detected. The source of the digital edge is specified using the Digital Edge Source attribute.
IQ Power Edge (2)	The Reference Trigger is asserted when the signal changes past the level specified by the slope (rising or falling), which is configured using the IQ Power Edge Source attribute.
Software (3)	The Reference Trigger is not asserted until a software trigger occurs.

UPLINK_SPREADING_LONG_CODE_MASK = 6291486

Specifies the long code mask for reverse link spreading.

You do not need to use a selector string to configure or read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

The default value is 0.

WALSH_CODE_LENGTH = 6291479

Specifies the Walsh code length of a specific user-defined channel. This value is expressed in chips. This attribute is used only when you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined.

Use “channel< <format type=”monospace-italic”>n</format> >” as the Selector String to configure or read this attribute.

The default value is 64.

WALSH_CODE_NUMBER = 6291480

Specifies the Walsh code number of a specific user-defined channel. This attribute is used only when you set the CHANNEL_CONFIGURATION_MODE attribute to User Defined.

Use “channel< <format type=”monospace-italic”>n</format> >” as the Selector String to configure or read this attribute.

The default value is 0.